Electronic Devices - Op-Amp Applications - Discussion
Discussion Forum : Op-Amp Applications - General Questions (Q.No. 2)
2.
Calculate the output voltage if V1 = –0.2 V and V2 = 0 V.
Discussion:
13 comments Page 1 of 2.
Seema Rajput said:
9 years ago
Vo = (-Rf/R1)V1 + (-Rf/R2)V2.
= (-330k/33k) * (- 0.2v) + (- 330/10k) * 0.
= (- 10) * (-0.2) + 0.
Vo = 2V.
= (-330k/33k) * (- 0.2v) + (- 330/10k) * 0.
= (- 10) * (-0.2) + 0.
Vo = 2V.
(9)
Raviraj said:
9 years ago
vo = -[330/33 (-0.2)] = 2v.
(5)
Neeharika said:
8 years ago
By nodal analysis (0 -V1)/33k+(0-V0)/330k = 0.
0.2/33k-V0/330k = 0.
V0 = 2v.
0.2/33k-V0/330k = 0.
V0 = 2v.
(4)
Surya said:
9 years ago
If the voltage source is connected to the positive terminal of an op amp and ground is connected to the negative terminal of the op amp then it's called as "non-inverting amplifier". If the terminals are reversed then acts as inverting amplifier.
(2)
Muhammad Younas said:
8 years ago
Good work, Thanks for explaining it.
(2)
Dipanjan said:
1 decade ago
Ii=(V1-0)/33 [Ii=input current through 33k)
If=(V0-0)/330 [If=feed back current through 330k)
I-=(Ii)+(If) [Kirchhoff law at opamp input node]
As input impedance of opamp is Infinite So Input current(I-) is zero.
(Ii)+(If)=0
Ii=-If
V1/33=-V0/330
V0=-10*V1=-10*(-0.2)=2V
If=(V0-0)/330 [If=feed back current through 330k)
I-=(Ii)+(If) [Kirchhoff law at opamp input node]
As input impedance of opamp is Infinite So Input current(I-) is zero.
(Ii)+(If)=0
Ii=-If
V1/33=-V0/330
V0=-10*V1=-10*(-0.2)=2V
(1)
Indu said:
1 decade ago
Here given the amplifier is summing opamp and the solution of the given problem.
vo = -[330/33 (-0.2)] = 2 v.
vo = -[330/33 (-0.2)] = 2 v.
(1)
Amit said:
8 years ago
As we see in the circuit, -o.2 is applied at the negative terminal so the op-amp is inverting op-amp. By general description, we calculate drop across 33k by ohms law. We get 1/165 amp and in other branches we applied same ohms law and we get 0 amp coz v=0v. Now add both the currents and applied again ohms law at feedback branch 330k we get vo= 2volt.
(1)
Amit bhattacharya said:
1 decade ago
As v2 is zero so that branch can be neglected
i.e. 10k can be neglected
Now the circuit is simple non inverting amp
and v0=(-Rf/R1)*v1
=-(330k/33k)*(-0.2)
=2v
i.e. 10k can be neglected
Now the circuit is simple non inverting amp
and v0=(-Rf/R1)*v1
=-(330k/33k)*(-0.2)
=2v
Vandana said:
1 decade ago
It is not a non inverting amplifier, it is an simple inverting amplifier. If it is a non inverting amplifier then formula for voltage output should be diffrent.
Post your comments here:
Quick links
Quantitative Aptitude
Verbal (English)
Reasoning
Programming
Interview
Placement Papers