IndiaBIX

Online Technical Drawing Test - Technical Drawing Test - Random

Instruction:
  • This is a FREE online test. Beware of scammers who ask for money to attend this test.
  • Total number of questions: 20.
  • Time allotted: 30 minutes.
  • Each question carries 1 mark; there are no negative marks.
  • DO NOT refresh the page.
  • All the best!

Marks : 2/20

Total number of questions
20
Number of answered questions
0
Number of unanswered questions
20
Test Review : View answers and explanation for this test.
1.
These types of projectors converge at a vanishing point:
Perspective
Parallel
Orthographic
Oblique
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Technical Sketching
2.
In oblique drawing, circles and angles perpendicular to the projection plane are true size and shape.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Technical Sketching
3.
This is a rounded exterior blend between surfaces:
Fillet
Round
Taper
Chamfer
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : 2D Drawing Representation
4.
When filling an area with a hatch pattern in AutoCAD the drafter needs to be able to ________.
see the entire bounding area to hatch
set Ortho on
turn ISO grid off
set the layer to Defpoints
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Sectional Views
5.
If you set the ANSI 131 hatch pattern to an angle of 45 degrees the lines will be placed vertically.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Sectional Views
6.
When a cutting plane coincides with a centerline, the cutting plane line takes precedence.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Sectional Views
7.
Tolerances of form and position are typically not used to control straightness.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Tolerancing
8.
Datum surfaces and features are used as references to control other features.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Tolerancing
9.
These are groups of components of a larger machine:
Subassemblies
External assemblies
Component assemblies
Major assemblies
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Working Drawings
10.
In isometric drawings, an angle may project to appear larger, but never smaller than the true angle depending on its position.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Axonometric Projection
11.
On a single contour line, all points have the same elevation.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Landform Drawings
12.
This type of drawing shows two lines representing the pipe diameter:
Single-line
Double-line
Standard piping
Centerline piping
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Piping Drawings
13.
Drafters usually begin a set of dimensions from the inside edge of an exterior wall.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Dimensioning Architectural Drawings
14.
The AutoCAD Center Mark tool can be used in an isometric drawing as you would use it in any conventional orthographic drawing.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Isometric Drawings
15.
A group of blocks stored in a drawing file is commonly referred to as a block library.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Blocks
16.
It is customary for the first sheet of a working drawing set to include ________.
a parts list
exploded assembly
assembled assembly
all of the above
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Mechanical Working Drawings
17.
A detail drawing of a part is intended to provide the necessary information needed to fabricate that part.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Mechanical Working Drawings
18.
BOM stands for Bill of Materials.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Mechanical Working Drawings
19.
Elevation drawings will include information about ________.
roof pitch
siding
window style
all of the above
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Architectural Working Drawings
20.
A set of working drawings used to build a house is considered a legal document.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Architectural Working Drawings
*** END OF THE TEST ***
Time Left: 00:29:56
Post your test result / feedback here:

Quick links
Quantitative Aptitude
Verbal (English)
Reasoning
Programming
Interview
Placement Papers