IndiaBIX

Online Technical Drawing Test - Technical Drawing Test 1

Instruction:
  • This is a FREE online test. Beware of scammers who ask for money to attend this test.
  • Total number of questions: 20.
  • Time allotted: 30 minutes.
  • Each question carries 1 mark; there are no negative marks.
  • DO NOT refresh the page.
  • All the best!

Marks : 2/20

Total number of questions
20
Number of answered questions
0
Number of unanswered questions
20
Test Review : View answers and explanation for this test.
1.
Orthographic projections have projectors that are parallel to the plane of projection.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Layouts and Lettering
2.
This type of solid is egg-shaped and can be created by revolving an ellipse around one of its axes:
Ellipsoid
Torus
Cone
Cylinder
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Technical Sketching
3.
An edge is formed where two surfaces intersect.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Technical Sketching
4.
The degree of precision of a given sketch depends on its use.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Technical Sketching
5.
A set of written specifications is often included in a set of technical drawings.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Technical Sketching
6.
In architectural drawing ________ are often used to illustrate and detail structural components.
Foundation beam detail sections
Wall sections
Building sections
All of the above
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Sectional Views
7.
The visible lines adjacent to a revolved section may be broken out if desired.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Sectional Views
8.
The pattern used for hatching a section can be something other than diagonal lines.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Sectional Views
9.
Tests of prototypes should simulate the conditions under which the product is to be used.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Manufacturing Processes
10.
When lines intersect on a drawing at angles of this many degrees, it is customary not to dimension the angle:
360
180
90
45
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Tolerancing
11.
This means that a feature of a finished product contains the maximum amount of material permitted by the toleranced dimensions for that feature:
Maximum material condition
Machined material condition
Maximum machined indication
Machine mark indication
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Tolerancing
12.
Implied 90 degree angles typically have different general tolerances applied to them than other angles covered by a general note.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Tolerancing
13.
Geometric tolerances state the maximum allowable variations of a form or its position from the perfect geometry implied in the drawing.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Tolerancing
14.
Detail drawings contain all of the necessary information to manufacture a part.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Working Drawings
15.
Using this as a communication and design review tool can help shorten the process and eliminate productivity barriers:
Development plans
Portable document files
The Internet and e-mail
Gantt charts
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Drawing Management
16.
In perspective drawings this is placed between the observer and the object:
Vanishing point / horizon
Station point
Ground line
Plane of projection / picture plane
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Perspective Drawings
17.
Perspective drawings are classified according to their number of these features:
Station points
Picture planes
Vanishing points
Ground lines
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Perspective Drawings
18.
The most common geometric form used in gears today is this:
Involute profile
Convolute profie
Base circle
Spur circle
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Gears and Cams
19.
If technical drawings are used to communicate size and shape descriptions, it is not important to worry about either the weight of a line or the type of line being used.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Multiview Drawing
20.
Blocks containing tags or labels of data are called Data Blocks.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Blocks
*** END OF THE TEST ***
Time Left: 00:29:56
Post your test result / feedback here:

Quick links
Quantitative Aptitude
Verbal (English)
Reasoning
Programming
Interview
Placement Papers