IndiaBIX

Online Technical Drawing Test - Technical Drawing Test 4

Instruction:
  • This is a FREE online test. Beware of scammers who ask for money to attend this test.
  • Total number of questions: 20.
  • Time allotted: 30 minutes.
  • Each question carries 1 mark; there are no negative marks.
  • DO NOT refresh the page.
  • All the best!

Marks : 2/20

Total number of questions
20
Number of answered questions
0
Number of unanswered questions
20
Test Review : View answers and explanation for this test.
1.
Enhancing product development is considered aesthetic design.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Graphic Language for Design
2.
The same general concepts and drafting standards apply to CAD as to drawings created by hand.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Layouts and Lettering
3.
Perspective pictorials approximate the view produced by the human eye.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Technical Sketching
4.
In a pictorial sketch you can see the width, height, and depth of an object in a single view.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Technical Sketching
5.
It is much easier for a drafter to use a CAD system rather than traditional board drawing because corrections are much easier to make.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Technical Sketching
6.
Knurl is a pattern form on a surface to provide for better gripping or more surface area for attachment.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : 2D Drawing Representation
7.
This type of section is limited by a break line:
Removed section
Revolved section
Broken-out section
Half section
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Sectional Views
8.
An intersection drawing is a flat representation or pattern that, when folded together, creates a 3D object.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Auxiliary Views
9.
Auxiliary views of 3-dimensional parts can be easily created with AutoCAD.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Auxiliary Views
10.
In reference to geometric tolerancing, the term "geometric" refers to forms such as planes, cylinders, and squares.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Tolerancing
11.
These gears transmit power between shafts whose axes intersect at any angle:
Worm gears
Spur gears
Bevel gears
Racks
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Gears and Cams
12.
This is a curve showing the displacement of the follower as ordinates on a base line that represents one revolution of the cam:
Displacement diagram
Follower
Cam cycle
Reciprocation chart
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Gears and Cams
13.
Due to wood loss in surfacing, the nominal size of structural timber is larger than its dressed thickness.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Structural Drawing
14.
Structural steel shop drawings are usually calculated to the nearest ½ inch.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Structural Drawing
15.
Riveting is seldom used as a connection method in structural steel.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Structural Drawing
16.
Most architectural drawings produced for field use by building contractors are printed on architectural "D" size paper which measures ________.
24" X 36"
18" X 24"
11" X 17"
34" X 22"
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Multiview Drawing
17.
A drafter can use the 45 degree triangle to draw a 30 degree line.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Traditional Drafting Techniques
18.
The architectural and construction industries use the United States National CAD standard (NCS) system on many ________ projects.
residential
commercial
aerospace
publicly funded
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Dimensioning Architectural Drawings
19.
Newer versions of AutoCAD utilize the ________ to make block library management very easy.
File / find
Design Center
File / search
None of the above
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Blocks
20.
The architectural drafter usually begins a set of working drawings by creating the ________ plan first.
foundation
floor plan
elevations
building section
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Architectural Working Drawings
*** END OF THE TEST ***
Time Left: 00:29:56
Post your test result / feedback here:

Quick links
Quantitative Aptitude
Verbal (English)
Reasoning
Programming
Interview
Placement Papers