IndiaBIX

Online Technical Drawing Test - Technical Drawing Test 6

Instruction:
  • This is a FREE online test. Beware of scammers who ask for money to attend this test.
  • Total number of questions: 20.
  • Time allotted: 30 minutes.
  • Each question carries 1 mark; there are no negative marks.
  • DO NOT refresh the page.
  • All the best!

Marks : 2/20

Total number of questions
20
Number of answered questions
0
Number of unanswered questions
20
Test Review : View answers and explanation for this test.
1.
PDM is the acronym for:
Project drawing management
Product drawing manipulation
Product data management
Project data manipulation
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Graphic Language for Design
2.
Idea or concept sketches are usually not considered to be technical drawings.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Graphic Language for Design
3.
The rear, left-side, front, and right-side views align horizontally.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Orthographic Projection
4.
The profile plane is the plane upon which the side view is projected.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Orthographic Projection
5.
When a part is cut fully in half, the resulting view is called a half section.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Sectional Views
6.
The visible edges of the object behind the cutting plane are not cross-hatched.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Sectional Views
7.
The angle of revolution should always be less than 45 degrees for an aligned section.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Sectional Views
8.
A primary auxiliary view does not need to be parallel to the associated inclined plane.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Auxiliary Views
9.
A worm is a screw with a thread shaped like a rack tooth.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Gears and Cams
10.
The bearing of a line is its angle from magnetic south.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Landform Drawings
11.
This type of drawing shows two lines representing the pipe diameter:
Single-line
Double-line
Standard piping
Centerline piping
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Piping Drawings
12.
Several of the tools used in traditional drafting include the following:
Parallel straight edge
45 degree triangle
Circle template
All of the above
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Traditional Drafting Techniques
13.
Dimensions are used on the elevation plan to describe ________.
Finished floor elevations
Roof overhangs
Roof pitch angles
All of the above
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Dimensioning Architectural Drawings
14.
When dimensioning architectural drawings architects will utilize both ________ and ________ options.
Baseline and continuous
Baseline and linear
Quick dim and linear
Linear and continuous
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Dimensioning Architectural Drawings
15.
Tolerances in an architectural drawing are just as close as tolerances used in mechanical drawings.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Dimensioning Architectural Drawings
16.
Before starting an isometric drawing in AutoCAD the drafter needs to ________.
set the grid to isometric
set the current layer to Defpoints
turn Object Snap off
turn Ortho off
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Isometric Drawings
17.
An isometric drawing is a type of technical drawing used to illustrate a mechanical part in true 3-dimensional form.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Isometric Drawings
18.
Problem identification has to do with the final stages in the mechanical design process.
True
False
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Mechanical Working Drawings
19.
To insure that everyone understands what the electrical symbols represent it is customary to include a ____ on the electrical sheet.
list
part number
electrical legend
electrical layer
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : Architectural Working Drawings
20.
The Press-Pull tool will ________ the face of a solid model in the direction it faces.
taper
extrude
spiral
none of the above
Your Answer: Option
(Not Answered)
Correct Answer: Option
Discuss about this problem : Discuss in Forum
Learn more problems on : 3D Modeling Basics
*** END OF THE TEST ***
Time Left: 00:29:56
Post your test result / feedback here:

Quick links
Quantitative Aptitude
Verbal (English)
Reasoning
Programming
Interview
Placement Papers